Advanced booting

MultiBoot

The process for setting up a multi-boot is very similar to Booting from a flash card. It's a good idea to makes sure the first partition is a fat/data partition - this keeps things simple.

A sample partition layout on an 8Gb card may be:

  • 2Gb primary vfat data
  • 2Gb primary everyday
  • 2Gb primary debian
  • 512Mb logical test1 (diablo)
  • 512Mb logical test2 (chinook)
  • 512Mb logical test3 (diablo)

Be aware that the kernel/initfs only supports a limited number of partitions; this can easily be extended to 6 but no further. This requires editing /home/user/local/bin/initfs_flasher/initfs.bootmenu.jffs2 to add the dev nodes using mknod (eg: mknod -m600 initfs/dev/mmcblk0p5 b 254 5)

When cloning, you may edit nupgrade.sh to remove the TARGET= line and then run it as follows:

TARGET=/dev/mmcblk0p5 ./nupgrade.sh 1

To create pristine images of Diablo/Chinook, follow the instructions for Modifying the root image, but once you have the rootfs.jffs2 image extracted, you can follow the mount instructions and rsync the rootfs to the tablet.

I used this script (which doesn't work yet)

#!/bin/bash

# This script connects to the tablet and sends the selected rootfs to the selected partition

FLASHER3=/everything/Downloads/Hardware/nokia_n800/flasher-3.0 
F_IMAGE=/everything/Downloads/Hardware/nokia_n800/RX-34_2008SE_2.2007.51-3_PR_COMBINED_MR0_ARM.bin
IMAGE_DIR=chinook_fiasco
PART=/dev/mmcblk0p6

mkdir -p $IMAGE_DIR
cd $IMAGE_DIR

# unpack fiasco
$FLASHER3 -F $F_IMAGE -u

# https://wiki.maemo.org/Modifying_the_root_image
mknod /tmp/mtdblock0 b 31 0
modprobe loop
losetup /dev/loop0 rootfs.jffs2 
modprobe block2mtd
modprobe mtdblock
echo "/dev/loop0,128KiB" > /sys/module/block2mtd/parameters/block2mtd
modprobe jffs2
mkdir /tmp/jffs2
mount -t jffs2 /tmp/mtdblock0 /tmp/jffs2

# copy files
ssh root@nut insmod /mnt/initfs/lib/modules/2.6.21-omap1/ext2.ko \; mkdir /tst \; mount $PART /tst
rsync -av /tmp/jffs2/ root@nut:/tst/
ssh root@nut umount /tst \; rmdir /tst

#clean up
umount /tmp/jffs2
rmmod jffs2
rmmod mtdblock
rmmod block2mtd
losetup -d /dev/loop0
rm -f /tmp/mtdblock0
rmdir /tmp/jffs2

Boot Messages

So if you want to see the kernel boot log or dmesg type output when you boot here's how (thanks to querty12 for the pointers)

Check you have an up-to-date initfs - does this file exist:

/mnt/initfs/usr/bin/fb_update_mode

If not then install fanoush's bootmenu/initfs.

Log into the tablet and remount initfs so you can edit it directly. (If this doesn't make you nervous then you should stop now!)

 mount -o remount,rw /mnt/initfs

Now grab some kernel modules from here:

 http://fanoush.wz.cz/maemo/modules-2.2007.50-2-custom.tar.gz

and copy the 4 modules you find in

  ./drivers/video/console/

to

 /mnt/initfs/lib/modules/`uname -r`/

I extracted them on my host and did:

 scp drivers/video/console/* root@nut:/mnt/initfs/lib/modules/2.6.21-omap1/

Now, for each bootmenu where you want a bootlog, edit /mnt/initfs/bootmenu.conf and add

 softcursor bitblit font fbcon

to any MODULE_N_MODULES= lines Also add a line like this:

 MENU_2_FBMODE="auto"

eg:

 MENU_4_NAME="Diablo Test"
 MENU_4_ID="mmc5"
 MENU_4_DEVICE="${INT_CARD}p5"
 MENU_4_MODULES="mbcache ext2 softcursor bitblit font fbcon"
 MENU_4_FSTYPE="ext2"
 MENU_4_FSOPTIONS="noatime"
 MENU_4_FBMODE="auto"
 [ -d "/sys/block/${INT_CARD}/${MENU_4_DEVICE}" ] || MENU_4_NAME="(${MENU_4_NAME}) N/A"

Finally, remount the initfs as ro and reboot.

 mount -oremount,ro /mnt/initfs/

Once your system starts, don't forget to run

 /mnt/initfs/usr/bin/fb_update_mode manual

or the display will run slowly.

Initfs Hacking