Editing Community SSU/Installation FAQ

Warning: You are not logged in. Your IP address will be recorded in this page's edit history.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.

Learn more about Contributing to the wiki.

'''Temporary Notice:
to update to CSSU-T5.1 you first have to update the operator name widget. Do NOT use "update all" button in Hildon Application Manager before you clicked on operator name to update that package first!

If you already did try to "update all" and got "use PC suite..." error message: quit HAM, wait 5 minutes, start HAM, wait, update operator name widget, wait, "update all".
'''

{{ambox|text=Most of the reasons on why the [[Community SSU|Maemo 5 Community SSU]] cannot be installed can be checked under the ''Problems'' tab when viewing the package in the Hildon Application Manager (HAM).
}}

'''Q: I can't update, as I get the message: TO UPDATE YOUR DEVICE TO THIS VERSION OF THE OPERATING SYSTEM YOU MUST USE NOKIA PC SUITE ON YOUR PC. CONNECT THE DEVICE TO YOUR PC VIA A USB CABLE AND LAUNCH THE APPLICATION.'''

'''A:''' The message is misleading. In the majority of the cases, it is either needed to free up some disk space or fix some conflicts with other packages. Before taking any action, check the the ''Problems'' tab when viewing the package in the Hildon Application Manager (HAM). Also see lower notes.

----

'''Q: I cannot install the Maemo 5 Community SSU Package because of xxxxx package'''

'''A:''' The best way to check out the source of the problem for this is to go into X Terminal and to use <code>apt-get</code> as root to install the package whilst Community SSU repository is enabled inside the Hildon Application Manager (HAM):

apt-get install ''package name that is causing the problem''

In most cases, users with the <code>modified-hildon-desktop</code> package installed will have issues updating the <code>hildon-desktop</code>. This  happens because the <code>modified-hildon-desktop</code> overwrites schemes set out by the normal <code>hildon-desktop</code> package. To alleviate this issue one needs to '''remove the <code>modified-hildon-desktop</code>''' before retrying.

In case there are a lot of packages causing the problem you may run the following command in X Terminal with root privileges:

apt-get update
  apt-get install mp-fremantle-community-pr

That will allow upgrade to the CSSU.

----

'''Q: I can't install the enabler; it says "not enough disk space available". How much is required?'''

'''A:''' stlpaul [http://talk.maemo.org/showpost.php?p=931491&postcount=7 reports] that he freed up 15MB from the rootfs and "then it worked".

----

'''Q: The installation of CSSU fails and HAM says something about catalogue problems.'''

'''A:''' The Community SSU installer cannot check if the CSSU catalogue or any other catalogue fails to update and does not continue in any case. Start the Application Manager '''before''' you do any of the installation steps. Try to update your catalogues and remove any non-working catalogues, that is those marked with a red "!") in the Settings.

----

'''Q: The installer doesn't reboot N900 - I only have a black screen with backlight!'''

'''A:''' You probably have wall charger or USB cable plugged in. That prevents normal shutdown from happening so you need to shut down the phone manually. Try pressing the power button and if you get to the power button menu, shut it down from there. If not, then hold down the power button for long enough to shut it down.

After this, start your N900 normally and you should have the CSSU installed - try for example the portrait mode menu.

----

'''Q: After installing version 20.2010.36-maemo14, my hildon-status-menu has no rows'''

'''A:''' 20.2010.36-maemo14 introduces configurable rows in hildon-status-menu, gconf should use the default value, but in some cases doesn't, the following commands should set back to default:
 gconftool-2 -s /apps/osso/hildon-status-menu/view/number_of_rows -t int 6
 gconftool-2 -s /apps/osso/hildon-status-menu/view/number_of_rows_portrait -t int 8

----

'''Q: How do I uninstall the CSSU?'''

'''A:''' This is not a fully supported operation at the moment, however the following notes may help:

# disable the CSSU repository in the package manager
# disable the [[extras-devel]] repository (if left enabled, the upgrade command might force unstable versions of currently installed applications or libraries)  
# uninstall <code>mp-fremantle-community-pr</code> using the package manager
# uninstall <code>mcsp</code> using the package manager
# uninstall ''Community SSU enabler'' using the package manager
# do an update check and install any that show up (or execute on the command line as root <code>apt-get update && apt-get upgrade</code>)
# As root, execute <code>apt-get install mp-fremantle-generic-pr</code>

'''This method is neither officially supported nor advised, and will usually result in a system with quite a number of problems. Only sane way to "uninstall" CSSU is to do a reflash of COMBINED aka rootfs, or to restore a backupmenu backup.'''

[[Category:Community]]
[[Category:Fremantle]]

Please note that all contributions to maemo.org wiki may be edited, altered, or removed by other contributors. If you do not want your writing to be edited mercilessly, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource (see maemo.org wiki:Copyrights for details). Do not submit copyrighted work without permission!

Summary:

Cancel | Editing help (opens in new window)

Templates used on this page:

Template:Ambox (view source) (semi-protected)

Retrieved from "https://wiki.maemo.org/Community_SSU/Installation_FAQ"

Latest revision		Your text
Line 13:		Line 13:


-	'''A:''' The message is misleading. In the majority of the cases, it is either needed to free up some disk space or fix some conflicts with other packages. Before taking any action, check the the ''Problems'' tab when viewing the package in the Hildon Application Manager (HAM). Also see notes ~~below~~.	+	'''A:''' The message is misleading. In the majority of the cases, it is either needed to free up some disk space or fix some conflicts with other packages. Before taking any action, check the the ''Problems'' tab when viewing the package in the Hildon Application Manager (HAM). Also see lower notes.

Personal tools

Navigation

Views

Editing Community SSU/Installation FAQ