Editing Gentoo/N900

Warning: You are not logged in. Your IP address will be recorded in this page's edit history.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.

Learn more about Contributing to the wiki.

This is the official page for the unofficial port of Gentoo to N900 internet tablets.

If you have any questions/troubles, you can find ''me'' (probably luke-jr) on freenode [irc://chat.freenode.net/maemo #maemo] and [irc://chat.freenode.net/gentoo-embededded #gentoo-embedded] ([http://webchat.freenode.net/?channels=%23Maemo,%23Gentoo-Embedded webchat]).

'''Bootable with X, WiFi, SMS, and GPRS'''

== Overview / Todo list ==
* <s>Main display</s>
* Battery charger daemon (or kernel integration)
* <s>Keyboard (X11)</s>
* <s>GPRS/UMTS data connections</s>
** <s>Integrated with Gentoo network subsystems</s>
* <s>SMS</s>
* Audio output (NOT SAFE: see highpass filter)
* Voice calls
** Cellular
** Ring/vibrate
** SIP
** XMPP
* <s>Front camera</s>
** Camera button
** Autofocus
* Usable GUI
** Razor-qt?
** KDE Plasma Active?
* Video calls (webcam)
** Skype support?
* Flashlight (SAFETY RESTRICTIONS NEEDED)
* GPS (gpsd driver)
** Road navigation
** Dead reckoning w/ accelerometers?
** [http://talk.maemo.org/showthread.php?t=72497 Cellular]
* [https://gitorious.org/community-ssu/maemo-tvout-control/trees/master/src TV out]
* FM transmitter
* Keyboard (console)
* Bluetooth
** Headset
** GPS
** ??
* Infrared transmitter
* 3D acceleration
* FM receiver

== Installation ==

=== Partitioning ===

If you use the internal memory card, be sure to leave your Maemo partitions in the same partition order as before (unless you don't want to run Maemo anymore, of course)

**Unless you're super-careful doing this, you will probably lose all the data on the partitions you change. Backup!**

First, dump your current partition layout:
 sfdisk -d /dev/mmcblk0 > ptable
Now, edit the ptable file with your favourite editor and load the modified one:
 sfdisk --no-reread /dev/mmcblk0 < ptable

Here is how I partitioned my internal SSD:
 unit: sectors
 /dev/mmcblk0p1 : start=       64, size=  4194304, Id= c
 /dev/mmcblk0p2 : start= 56631360, size=  4194304, Id=83
 /dev/mmcblk0p3 : start= 60825664, size=  1572864, Id=82
 /dev/mmcblk0p4 : start=  4194368, size= 52436992, Id= 5
 /dev/mmcblk0p5 : start=  4194384, size= 20971568, Id=83
 /dev/mmcblk0p6 : start= 25165968, size= 31465392, Id=83

If you're more conforable with standard Linux fdisk, [https://garage.maemo.org/plugins/wiki/index.php?RepartitionInstructions&id=1382&type=g supposedly] [http://archive.debian.org/debian/pool/main/u/util-linux/util-linux_2.13.1.1-1_armel.deb the deb from Debian Lenny] works.
See the [http://www.gentoo.org/doc/en/handbook/handbook-arm.xml?part=1&chap=4#doc_chap3 official Gentoo handbook] if you need help using fdisk to edit your partition table.

===Creating Filesystems===

Since you are installing on a SSD that may very well queue its writes out of order, ext3 and other journaling filesystems designed for magnetic/write-in-order drives are generally a bad idea and may be very dangerous to use.
If you're using an old kernel, such as the original Fremantle kernel, you'll have to stick to ext2. If you are using a recent "power" kernel (or modern kernel), you can use ext4 without journal support (but possibly these do not have ext4 ACLs/xattrs enabled).

I recommend making swap on an external MicroSD so when you destroy it, it can be replaced (unlike the internal one).

===Mounting===

Due to Maemo using the FHS /media for other partitions, I chose to use it for the Gentoo mount too. You can use Gentoo's standard /mnt here if you want, I think.

mount -t ext2 /dev/mmcblk0p5 /mnt/gentoo

===Installing Gentoo===

Be sure your system clock is correct before proceeding. Weird things happen when it's not.

Download [http://distfiles.gentoo.org/experimental/arm/musl/ the latest *vanilla* armv7a_hardfp musl stage3 from Gentoo].
Note that standard glibc stage3 will no longer work as it includes glibc 2.20, which is incompatible with the older kernels needed for N900.
You could try uclibc instead, but nobody has tried that thus far, so you're on your own.

Just in case, download the .DIGESTS file too, and verify your download with:
 grep -A1 SHA512 stage3-*DIGESTS | sha512sum -c

Now, proceed to unpack the stage3:
 cd /media/gentoo
 tar xvjpf stage3-*.tar.bz2

Configure your compile options (/media/gentoo/etc/portage/make.conf) next.

Recommended (only safe to use unmodified for musl hardfp ABI!):
 CHOST="armv7a-hardfloat-linux-musleabi"
 # WARNING: -mthumb -mthumb-interwork require a Thumb-safe kernel! Remove them otherwise.
 CFLAGS="-O2 -pipe -mcpu=cortex-a8 -mfpu=neon -mfloat-abi=hard -mthumb -mthumb-interwork"
 CXXFLAGS="${CFLAGS}"
 ASFLAGS="-mcpu=cortex-a8 -mfpu=neon -mfloat-abi=hard -mthumb -mthumb-interwork"
 
 # Distcc is a good idea, if you [http://www.gentoo.org/doc/en/cross-compiling-distcc.xml setup a cross-compiler on another Gentoo system]
 FEATURES="${FEATURES} distcc"
 # MAKEOPTS -jN should probably be the number of systems in your distcc array; but never more than 2 when building KDE software (meinproc uses a lot of memory and won't be distributed)!
 MAKEOPTS="-j2"
 
 # Since the N900 doesn't have a lot of RAM, you'll probably need to sacrifice some CPU time to minimize memory usage
 LDFLAGS="${LDFLAGS} -Wl,--no-keep-memory -Wl,--reduce-memory-overheads"
 # The following thing increased building times of some packages (paludis and cryptography, for instance) insanely and the man page suggests it is of questionable utility
 CFLAGS="${CFLAGS} --param ggc-min-expand=0 --param ggc-min-heapsize=32768"
 
 PORTAGE_NICENESS="10"
 PORTAGE_IONICE_COMMAND="ionice -c 3 -p \${PID}"

===Chroot===
 cp -L /etc/resolv.conf etc/
 mount -t proc proc proc
 mount -o bind /dev dev
 mount -t devpts devpts dev/pts
 env -i chroot . /bin/bash
 env-update
 source /etc/profile
 export PS1="(chroot) $PS1"

===Install and configure the Portage tree, with N900 overlay===
 emerge --sync --quiet
 USE='-* git curl ssl curl_ssl_openssl python_targets_python2_7' emerge layman
 # be sure to follow layman post-install instructions to edit make.conf
 layman -fa n900
 eselect profile set n900:n900/armv7a-hardfloat-linux-musleabi
 layman -a musl

===Configure timezone===
 USE=-nls emerge -1 timezone-data
 ls /usr/share/zoneinfo
 echo "UTC" > /etc/timezone
 emerge --config timezone-data

==Booting==

===Configuring your kernel===
If you just want to use your Maemo kernel, simply copy /lib/modules/* from your Maemo partition into Gentoo (you'll need to exit the chroot first) and emerge the appropriate kernel sources: fremantle-sources, fremantle-power-sources, and meego-sources are available.

However, if you want to build one yourself (required for any custom kernel modules, or non-X11 console), follow these steps:
 emerge fremantle-power-sources
 cd /usr/src/linux
 make menuconfig
 # (configure the kernel as you like here)
 make && make modules_install
 # (copy arch/arm/boot/zImage to your host system to flash as the N900's kernel)

Note that this kernel will not boot Maemo without setting up the modules on the Maemo partition. I believe this is as simple as copying the directory and running depmod on that side, but I'll have to review it before I'm sure.

===Configuring your system etc===
All of these are optional if you just want a chroot.

The following steps from Gentoo's official handbook are just fine here:
* [https://wiki.gentoo.org/wiki/Handbook:X86/Full/Installation#Filesystem_information Filesystem information]
* [https://wiki.gentoo.org/wiki/Handbook:X86/Full/Installation#Networking_information Networking information]
* [https://wiki.gentoo.org/wiki/Handbook:X86/Full/Installation#System_information System information]
* [https://wiki.gentoo.org/wiki/Handbook:X86/Full/Installation#System_logger System logger]
* [https://wiki.gentoo.org/wiki/Handbook:X86/Full/Installation#Optional:_Cron_daemon Optional: Cron daemon]
* [https://wiki.gentoo.org/wiki/Handbook:X86/Full/Installation#Optional:_File_indexing Optional: File indexing]
* [https://wiki.gentoo.org/wiki/Handbook:X86/Full/Installation#Optional:_Remote_access Optional: Remote access]
* [https://wiki.gentoo.org/wiki/Handbook:X86/Full/Installation#Filesystem_tools Filesystem tools]
* [https://wiki.gentoo.org/wiki/Handbook:X86/Full/Installation#Networking_tools Networking tools]

===Installing N900-required stuff===
The n900-env metapackage should pull in all the essentials for your N900.
If you don't want some N900 functionality, you can change your USE flags in make.conf prior to installing it.

{| class="wikitable"
! USE flag !! Description
|-
| bluetooth || BlueZ and Bluetooth firmware
|-
| cellular or gps || Ofono
|-
| nokia-osso-linux || Maemo "bootmenu" compatibility
|-
| v4l || Camera firmware
|-
| wifi || Wifi firmware and tools
|-
| X || X11 drivers
|}

emerge n900-env

==X11 setup==
Create /etc/X11/xorg.conf with the following:
 Section "Device"
     Identifier "Configured Video Device"
     Driver "omapfb"
     Option "fb" "/dev/fb0"
 EndSection
 
 Section "InputClass"
     Identifier "calibration"
     MatchProduct "TSC2005 touchscreen"
     Option "Calibration" "194 3901 3739 241"
 EndSection
 
 Section "InputClass"
     Identifier  "keyboard"
     MatchProduct    "omap_twl4030keypad"
 
     Option "XkbOptions" "grp:ctrl_shift_toggle"
     Option "XkbLayout" "nokia_vndr/rx-51(common)+nokia_vndr/rx-51(us)"
     Option "XkbModel" "nokia"
 EndSection
 
 Section "InputClass"
     Identifier "touchscreen"
     MatchProduct "TSC2005 touchscreen"
 
     Driver "tslib"
     Option "EmulateRightButton"    "1"
 EndSection

==Sound setup==

This basically "just works", but be careful when unmuting - it's possible to play audio that destroys the internal speakers! If you're experienced in writing highpass filters, please contact me to help resolve this.

==Cellular setup==

=== Install Ofono ===
 emerge net-misc/ofono

===Configure GPRS networking===
 ln -s net.lo /etc/init.d/net.gprs0
Edit /etc/conf.d/net:
 rc_need_gprs0='ofono'
 modem_gprs0='n9000'  # The extra zero is the n900 instance number 0 :)
 context_apn_gprs0='epc-scpcf000.t-mobile.com'  # Other providers need other APNs!
 context_protocol_gprs0='ipv6'

Start the GPRS interface:
 /etc/init.d/net.gprs0 start

=== Send SMS ===
 ofono-send-sms n9000 15555551212 'Hey there!'

=== Voice call ===
 ofono-dial-number n9000 15555551212

Note the other end will probably get silence, and you won't hear them either.
I'm working on an ALSA plugin to fix this.

== WiFi setup ==

ln -s net.lo /etc/init.d/net.wlan0
Edit /etc/conf.d/net:
 mac_wlan0='00:1f:df:xx:xx:xx'  # You MUST set this, or N900's wlan MAC won't be initialized!
 preferred_aps='my_wep_network my_public_network linksys etc'
 key_my_wep_network='abcd-ef00-1234-5678-9abc-def0-12'
 modules="!wpa_supplicant"

Start the wlan interface:
 /etc/init.d/net.wlan0 start

==Bluetooth setup==

It's on my todo list, but not very high priority since I don't really use anything Bluetooth...

==GPS setup==

I've reverse engineered the cellmo GPS protocols, and written [http://luke.dashjr.org/tmp/code/gps3.c a NMEA proxy] that mostly works with gpsd. When I get to properly integrating GPS support, I plan to write an actual gpsd driver so a proxy isn't needed.

==Known problems==
===Webkit linking memory usage===
WebKit requires an absurd amount of memory to link. I build binary packages inside qemu when it needs to be bumped. I suggest you use them.

==Modern kernel==
Current status: http://elinux.org/N900

Please note that all contributions to maemo.org wiki may be edited, altered, or removed by other contributors. If you do not want your writing to be edited mercilessly, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource (see maemo.org wiki:Copyrights for details). Do not submit copyrighted work without permission!

Summary:

Cancel | Editing help (opens in new window)

Retrieved from "https://wiki.maemo.org/Gentoo/N900"

Personal tools

Navigation

Views

Editing Gentoo/N900

@@ Line 48: / Line 48: @@
 If you use the internal memory card, be sure to leave your Maemo partitions in the same partition order as before (unless you don't want to run Maemo anymore, of course)
-'''Unless you're super-careful doing this, you will probably lose all the data on the partitions you change. Backup!'''
+**Unless you're super-careful doing this, you will probably lose all the data on the partitions you change. Backup!**
 First, dump your current partition layout: