Bme replacement
(→1. Premature shutdown) |
(→2. Battery applet showing wrong value for capacity) |
||
| Line 56: | Line 56: | ||
[14:17] <kerio> 4) bq27200 is our lord, bq27200 is our ruler, bq27200 is our saviour - when calibrated, /everything/ should be grabbed from bq27200 and that's it - percentages, capacity (when full and at the moment) | [14:17] <kerio> 4) bq27200 is our lord, bq27200 is our ruler, bq27200 is our saviour - when calibrated, /everything/ should be grabbed from bq27200 and that's it - percentages, capacity (when full and at the moment) | ||
| + | |||
| + | * Pali: add gconf value (int) for using maximal (design) capacity from rx51_battery. 0 - never, 1 - when not calibrated, 2 - always. Default value 1. TODO: hald-addon-bme must always report some value for design capacity. So what to show for gconf value 0? | ||
==3. bq27x00_battery sysfs node reports -ENODATA when not calibrated== | ==3. bq27x00_battery sysfs node reports -ENODATA when not calibrated== | ||
Revision as of 15:48, 26 March 2013
Contents |
Introduction
BME Replacement is a project aiming to bring proper FOSS replacement to Maemo's BME bits. It consists of both kernel and userland bits, cooperating, and make use of data provided by build-in hardware bq27x00 chip.
Unlike vanilla BME, replacement fully support USB hostmode, via usbmode.
Prerequisities
Kernel which provides bq2415x_charger, bq27x00_battery and rx51_battery modules. It also need to have "glue" between bq2415x_charger and monolitic musb driver. In practice, it means kernel-power52 or above (See: Kernel_Power)
Current state
Beta
.debs are available from: https://atrey.karlin.mff.cuni.cz/~pali/rx51-bme-replacement/ (might need to ignore expired certificate)
It works for everyday usage, but some major problems were found, see below.
Problems/bugs and proposed solutions
1. Premature shutdown
Device is shutting down at EDV1 voltage, not allowing bq27x00 chip to calibrate capacity. Calibrating require device to be *at or below* EDV1 for 15 seconds straight - going above even for a split second resets timer, so another straight 15 seconds is required.
Proposed solutions
1. gconf value, that allow power users to change voltage, at which device shutdowns to any arbitrary value.
This is preffered solution, as some devices are more like to have problems with GSM chip restarting at low voltage, even around EDV1 3248 mV. People with such problems, that preffer GSM stability over calibration, could bump voltage treeshold, to avoid problems. OTOH, people with less picky devices and/or dual-cell setups, could decrease limit, getting more from their batteries.
This method can be also augmented by solution 2, for "default" shutdown treeshold.
---
2. Using EDV1 flag, instead of EDV1 voltage, as trigger to shut device down. EDV1 *flag* being set, means, that device was just calibrated - it spares need complicated replication of 15 sec. calibration timer, mentioned in problem description.
EDV1 flag can be read from /sys/class/power_supply/bq24150a-0/registers address 0x55 0x0A, divided by 2.
2.a In case of EDV1 flag being not available*, fallback to using 3150 mV as shutdown treeshold. Rationale: 3150 mV shouldn't cause GSM chip restarts on devices, where 3248 mV haven't caused it already.
It doesn't guarantee calibration, as it require 15 seconds *straight* below 3248 mV (EDV1 voltage), and 3150 mV might be just momentary low voltage spike. But, it is better than current implementation, which permits calibration *ever* - and, after all, it is just theoretical fallback for hyphotetical, non-existing kernel.
* theoretical possibility with custom kernels, that fullfill basic requiments, but don't feed all data - currently, no such kernel exist
---
- Pali: Add two gconf values. First (bool) to enable shutdown device at EDV1 flag, second (int) to shutdown device at specified <= voltage. Default values: bool = true and int = 3150 (as suggested)
2. Battery applet showing wrong value for capacity
[14:15] <kerio> 2) instead of showing wildly inaccurate data, it's preferrable to show nothing, or a message indicating that data is unavailable
[14:16] <kerio> 3) f[censored] rx51-battery, given 2) there's no reason whatsoever to use it (except the temperature thing, but that's for dsme and pulseaudio, not for the battery/charging)
[14:17] <kerio> 4) bq27200 is our lord, bq27200 is our ruler, bq27200 is our saviour - when calibrated, /everything/ should be grabbed from bq27200 and that's it - percentages, capacity (when full and at the moment)
- Pali: add gconf value (int) for using maximal (design) capacity from rx51_battery. 0 - never, 1 - when not calibrated, 2 - always. Default value 1. TODO: hald-addon-bme must always report some value for design capacity. So what to show for gconf value 0?
3. bq27x00_battery sysfs node reports -ENODATA when not calibrated
It is a very serious problem, as CI flag (calibration needed) is set, when >32 charging cycles since last calibration. This result in dropping data, even if it is perfectly correct.
CI flag is set also, when battery isn't inserted into device for few minutes (in some devices, even few seconds).
In both cases, all scripts/programs that depends on those sysfsnodes breaks, due to "data read error". Also, -ENODATA is wrong, as in fact, chip report value for LMD (Last Measured Discharge) it is ILMD, default value of 2056 mAh. It should be provided by sysfs node, even, if not accurate - in any case, it's better than -ENODATA or "read error".
Proposed solutions
1. Fixing module, to always report value via sysfs node, as provided by hardware. Also, modifying those BME replacement bits, that require correct data, to watch for CI flag.
---