User:Mohammad7410/Packaging
Line 62: Line 62:
  Description: Sample package to show how packaging works
  Description: Sample package to show how packaging works
   Long description of the application to be shown if a user clicks Description in HAM
   Long description of the application to be shown if a user clicks Description in HAM
 +
 +
changelog:
 +
source_name (version_number) unstable; urgency=low
 +
 +
  * Initial release.
 +
 +
  -- Mohammad Abu-Garbeyyeh <mohammad7410@gmail.com>  Sun, 10 Oct 2010 23:31:54 +0200
 +
 +
Example:
 +
maemodeb (0.1) unstable; urgency=low
 +
 +
  * Initial release.
 +
 +
  -- Mohammad Abu-Garbeyyeh <mohammad7410@gmail.com>  Sun, 10 Oct 2010 23:31:54 +0200
 +
 +
This file can further be edited using dch, part of the package devscripts, apt-get install devscripts.
 +
 +
compat file:
 +
5
 +
 +
rules file:
 +
This is the only part of packaging where you have to think what to do, you will need to add the parts needed to configure-stamp, for example ./configure should be added there, or qmake if you're using Qt and a .pro file.
 +
 +
You will need to add the parts to compile the files to build-stamp, e.g make.
 +
And finally, the parts needed to install the file, e.g $(MAKE) DESTDIR=$(CURDIR)/debian/package_name install.
 +
If your make file does not handle file installations, you can use an install file in debian/ and keep dh_install in the rules file, as per below.
 +
#!/usr/bin/make -f
 +
# -*- makefile -*-
 +
# Sample debian/rules that uses debhelper.
 +
# This file was originally written by Joey Hess and Craig Small.
 +
# As a special exception, when this file is copied by dh-make into a
 +
# dh-make output file, you may use that output file without restriction.
 +
# This special exception was added by Craig Small in version 0.37 of dh-make.
 +
 +
# Uncomment this to turn on verbose mode.
 +
#export DH_VERBOSE=1
 +
 +
CFLAGS = -Wall -g
 +
 +
ifneq (,$(findstring noopt,$(DEB_BUILD_OPTIONS)))
 +
  CFLAGS += -O0
 +
else
 +
CFLAGS += -O2
 +
endif
 +
 +
configure: configure-stamp
 +
configure-stamp:
 +
dh_testdir
 +
# Add here commands to configure the package.
 +
 +
touch configure-stamp
 +
 +
 +
build: build-stamp
 +
 +
build-stamp: configure-stamp
 +
dh_testdir
 +
touch build-stamp
 +
 +
clean:
 +
dh_testdir
 +
dh_testroot
 +
rm -f build-stamp configure-stamp
 +
dh_clean
 +
 +
install: build
 +
dh_testdir
 +
dh_testroot
 +
dh_clean -k
 +
dh_installdirs
 +
dh_install
 +
 +
# Build architecture-independent files here.
 +
binary-indep: build install
 +
# We have nothing to do by default.
 +
 +
# Build architecture-dependent files here.
 +
binary-arch: build install
 +
dh_testdir
 +
dh_testroot
 +
dh_installchangelogs debian/changelog
 +
dh_installdocs
 +
dh_installexamples
 +
# dh_install
 +
# dh_installmenu
 +
# dh_installdebconf
 +
# dh_installlogrotate
 +
# dh_installemacsen
 +
# dh_installpam
 +
# dh_installmime
 +
# dh_python
 +
# dh_installinit
 +
# dh_installcron
 +
# dh_installinfo
 +
dh_installman
 +
dh_link
 +
dh_strip
 +
dh_compress
 +
dh_fixperms
 +
# dh_perl
 +
# dh_makeshlibs
 +
dh_installdeb
 +
dh_shlibdeps
 +
dh_gencontrol
 +
dh_md5sums
 +
dh_builddeb
 +
 +
binary: binary-indep binary-arch
 +
.PHONY: build clean binary-indep binary-arch binary install configure
 +
 +
Sample install file:
 +
bin/psfreedom-enable-n900.sh usr/sbin
 +
bin/psfreedom-disable-n900.sh usr/sbin
 +
bin/psfreedommoduledetection.sh usr/sbin
 +
bin/psfreedom usr/bin
 +
src/ui/PSFreedom opt/psfreedom
 +
data/psfreedom.sudoers etc/sudoers.d
 +
data/psfreedomicon.png usr/share/pixmaps
 +
data/psfreedom.desktop usr/share/applications/hildon

Revision as of 11:50, 14 November 2010

Packaging is the simplest, yet not exactly clearly documented well part of software development. This tutorial should hopefully cover everything you need to start making simple, working packages for Maemo.

This tutorial assumes you're running on Linux (or a virtual machine of one) and that you have Scratchbox installed as per http://wiki.maemo.org/Documentation/Maemo5_Final_Installation

Qt Creator users

A project made with QtCreator usually creates two (or more) folders, one contains a clean source, and the other contains an architecture specific build, for the purpose of this tutorial, we will not be using Qt Creator's package builder (as imo, it's crap compared to the manual one).

Copy the files in the clean source directory to somewhere in your scratchbox $home directory (or just copy the whole folder into ~ on scratchbox) and follow the steps below.

Scratchbox users

Packaging an application involves two things, getting the source itself, and making the debian/ directory and writing its contents. The debian/ directory is needed to make .deb packages, everything related to the package (i.e. .deb file) is there, with the sources outside it, the sources and the debian/ directory should be in one main directory, which is the source directory for the package.

Example hierarchy (Package name is maemodeb): 

maemodeb/ (main source dir, a version number can be appended (e.g maemodeb-0.1)
  src/ (usually contains sources, sources can also be put in the main dir without a subfolder)
  data/ (usually contains data, i.e icons/images)
  debian/ (contains the files needed to build the package)

The debian directory should contain at least this basic set of files, without them, a package cannot be built:

A control file, this holds information such as name of package(s - multiple packages can be built from one source), description, maintainer name, section, packages needed to build the source, and the dependencies, and (for Maemo), icons for the application manager and "pretty" names, also for the application manager.

A changelog file, this holds again, the name of the source (not the separate packages), the version number, the changes in that version number, and a signature with the name and email for the person who edited the old source, as well as a timestamp, this file can be auto-generated with dch.

A compat file, which contains the version of debhelper needed, only a number is held in this file, usually 5.

A rules file, which contains the build instructions.

What should these files contain? These files can be generated using dh_make, however, I find cleaning the examples it generates a bit tedious, so I copy the files from my own sample debian/ folder.

control file: 

Source: source_name
Section: section_goes_here, possible sections listed here http://wiki.maemo.org/Packaging#Sections
Priority: extra
Maintainer: Your_FULL_REAL_name <email_must_NOT_be_fake>
Build-Depends: debhelper (>= 5) # deps needed to build the package (e.g libqt4-dev for 
Standards-Version: 3.7.2

Package: first_package_name
XB-Maemo-Display-Name: Name to be displayed in HAM
Architecture: architecture, can be all/i386/armel
Depends: dependencies for the package
Description: short description here
 hildon-theme-alpha's boxes have a black border around theme, this package fixes the size 70 one.

Example: 

Source: maemodeb
Section: user/system
Priority: extra
Maintainer: Mohammad Abu-Garbeyyeh <mohammad7410@gmail.com>
Build-Depends: debhelper (>= 5)
Standards-Version: 3.7.2

Package: maemodeb
XB-Maemo-Display-Name: Maemo Deb
Architecture: all
Depends: apt, ${shlibs:Depends}
Description: Sample package to show how packaging works
 Long description of the application to be shown if a user clicks Description in HAM

changelog: 

source_name (version_number) unstable; urgency=low

  * Initial release.

 -- Mohammad Abu-Garbeyyeh <mohammad7410@gmail.com>  Sun, 10 Oct 2010 23:31:54 +0200

Example: 

maemodeb (0.1) unstable; urgency=low

  * Initial release.

 -- Mohammad Abu-Garbeyyeh <mohammad7410@gmail.com>  Sun, 10 Oct 2010 23:31:54 +0200

This file can further be edited using dch, part of the package devscripts, apt-get install devscripts.

compat file: 

5

rules file: This is the only part of packaging where you have to think what to do, you will need to add the parts needed to configure-stamp, for example ./configure should be added there, or qmake if you're using Qt and a .pro file.

You will need to add the parts to compile the files to build-stamp, e.g make. And finally, the parts needed to install the file, e.g $(MAKE) DESTDIR=$(CURDIR)/debian/package_name install. If your make file does not handle file installations, you can use an install file in debian/ and keep dh_install in the rules file, as per below. 

#!/usr/bin/make -f
# -*- makefile -*-
# Sample debian/rules that uses debhelper.
# This file was originally written by Joey Hess and Craig Small.
# As a special exception, when this file is copied by dh-make into a
# dh-make output file, you may use that output file without restriction.
# This special exception was added by Craig Small in version 0.37 of dh-make.

# Uncomment this to turn on verbose mode.
#export DH_VERBOSE=1

CFLAGS = -Wall -g

ifneq (,$(findstring noopt,$(DEB_BUILD_OPTIONS)))
 	CFLAGS += -O0
else
	CFLAGS += -O2
endif

configure: configure-stamp
configure-stamp:
	dh_testdir
	# Add here commands to configure the package.

	touch configure-stamp


build: build-stamp

build-stamp: configure-stamp
	dh_testdir
	touch build-stamp

clean:
	dh_testdir
	dh_testroot
	rm -f build-stamp configure-stamp
	dh_clean

install: build
	dh_testdir
	dh_testroot
	dh_clean -k
	dh_installdirs
	dh_install

# Build architecture-independent files here.
binary-indep: build install
# We have nothing to do by default.

# Build architecture-dependent files here.
binary-arch: build install
	dh_testdir
	dh_testroot
	dh_installchangelogs debian/changelog
	dh_installdocs
	dh_installexamples
# 	dh_install
#	dh_installmenu
#	dh_installdebconf
#	dh_installlogrotate
#	dh_installemacsen
#	dh_installpam
#	dh_installmime
#	dh_python
#	dh_installinit
#	dh_installcron
#	dh_installinfo 
	dh_installman
	dh_link
	dh_strip
	dh_compress
	dh_fixperms
#	dh_perl
#	dh_makeshlibs
	dh_installdeb
	dh_shlibdeps
	dh_gencontrol
	dh_md5sums
	dh_builddeb

binary: binary-indep binary-arch
.PHONY: build clean binary-indep binary-arch binary install configure

Sample install file: 

bin/psfreedom-enable-n900.sh		usr/sbin
bin/psfreedom-disable-n900.sh		usr/sbin
bin/psfreedommoduledetection.sh		usr/sbin
bin/psfreedom				usr/bin
src/ui/PSFreedom			opt/psfreedom
data/psfreedom.sudoers			etc/sudoers.d
data/psfreedomicon.png			usr/share/pixmaps
data/psfreedom.desktop			usr/share/applications/hildon
Retrieved from "http://wiki.maemo.org/User:Mohammad7410/Packaging"