Editing Changing the eMMC filesystem

Warning: You are not logged in. Your IP address will be recorded in this page's edit history.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.

Learn more about Contributing to the wiki.

As with most computers, the speed of the N900's internal storage often poses a bottleneck, slowing down the device during heavy reads/writes. Changing the filesystem can mitigate the impact of this.

By choosing an appropriate filesystem for the content of your disk, you are able to speed things up. Vice versa, a bad filesystem choice can negatively impact performance. A different reason to switch filesystems besides performance reasons can be because of the feature set offered by different filesystems. For example, ext3 is considered mostly as a very stable filesystem while Reiser4 offers transparent compression.

Each filesystem got its own pros and cons. There is no 'one size fits all' type of filesystem; only filesystems each with their own use-cases. Therefore: do some extensive research before deciding to change your filesystem!

This wiki page is focused on changing the filesystem of the <code>/home</code> partition.

Prerequisites:
*The kernel you're running should support the filesystem you want to use. Either use [[Kernel Power|kernel-power]] or compile a kernel yourself.
*Willingness to mess with Maemo's boot process (reflash risk!)

== How to do it ==
Basically, you need to move <code>/home</code> to a temporary location, reformat its original partition with the filesystem of your choice, copy <code>/home</code> back and finally edit <code>/etc/event.d/rcS-late</code>. This can be a challenge as Maemo gets into a reboot loop when <code>/home</code> can't be mounted. Back up all your data!

=== Solution #1: Do everything on-device ===
This solution is based on Solution #8 in [[Repartitioning_the_flash]].

<ol>
<li>
Move <code>/home</code> as described in Solution #8 in [[Repartitioning_the_flash]]. Follow the described steps strictly until you reach the command which would actually repartition the flash (the sfdisk command). You don't need to follow any other steps from the mentioned solution from now onwards.
</li>
<li>
Assuming you've successfully moved <code>/home</code> (e.g. you got a fully booted phone with <code>/home</code> on a different partition), format <code>/home</code> its original partition to your filesystem of choice and mount it. For example:
<pre>
mkfs.ext4 /dev/mmcblk0p2
mount -t ext4 -o rw,noatime,commit=1,data=writeback /dev/mmcblk0p2 /mnt
</pre>
</li>
<li>
Copy your <code>/home</code> back to (now its reformatted) original partition:
<pre>
cp -a /home/* /mnt
</pre>
Don't forget to unmount <code>/home/user/MyDocs</code> prior to copying!
</li>
<li>
Now you should edit <code>/etc/event.d/rcS-late</code> to make Maemo use <code>/home</code> its original partition again and accept its new filesystem type. 
<ol>
<li>
''Making Maemo use <code>/home</code> its original partition again.''

In step 1, you've added two lines:
<pre>
echo "/dev/mmcblk1p1 /home ext3 rw,noatime,errors=continue,commit=1,data=writeback 0 0" >> $tmp_fstab
echo "/home/opt /opt none bind" >> $tmp_fstab

</pre>
to <code>/etc/event.d/rcS-late</code>. For ext4 (or any ext), remove both lines.

For other filesystems, remove only second line (containing /opt) and modify first one, to include appropriate mount options for filesystem of Your choose: 
<pre>
#Reiser4 example
echo "/dev/mmcblk0p2 /home reiser4 rw,noatime 0 0" >> $tmp_fstab
</pre>
Make sure you add no invalid mount options! Mount failure results in a reboot-loop. You can test the mount options by trying to mount the partition manually prior to making it permanent.
</li>
<li>
''Making Maemo accept the new filesystem type.''

Line no. 12, 17, 22, 23 and 25 of rcS-late got "ext3" hard-coded in it (line 9 contains ext3 in comment, but this don't affect funcionality of script - You can change it if You want). We need to edit these lines to represent our new filesystem. 
Ext4 example:
<pre>
##Begin of snippet
script
    #mount /home; fix ext4 and retry mounting if 1st attempt fails
    mount_home ()
    {
    /bin/mount /home && grep -q "/home ext4 rw" /proc/mounts
    if [ $? -eq 0 ]
    then
      return 0
    else
      grep -q "/home ext4 ro" /proc/mounts
      if [ $? -eq 0 ]
      then
        umount /home
      fi
      HOME_DEV=`grep "/home ext4" /etc/fstab | cut -d' ' -f1`
      fsck.ext4 -y $HOME_DEV >> /var/lib/fsck_ext4_home.log 2>&1
      sync
      /bin/mount /home && grep -q "/home ext4 rw" /proc/mounts
      return $?
    fi
    }
##End of snippet
</pre>
Make sure line 23 contains a valid fsck.X command. Try running the command with all its parameters manually before making it permanent.

File <code>/usr/lib/genfstab.awk</code> also contain ext3 hardcoded in it (line 19 in vanilla Maemo, line 20 in latest CSSU-Testing). For switching to another ext filesystem (like ext4) change it to appropriate value.

<code>//Note for Geeks:</code>
Original creator of this article didn't mention that You need to modify <code>/usr/lib/genfstab.awk</code> - instead, he suggested to keep 1st line added to <code>/etc/event.d/rcS-late</code>. This probably allowed to go around omitted modification of <code>/usr/lib/genfstab.awk</code>, but approach proposed now is more accurate to native way how Maemo do it. Ho ever, i only tested it using ext4 filesystem - that have identical mount options (except stating that it's ext4) as ext3. I don't know if editing <code>/usr/lib/genfstab.awk</code> will work with filesystems other than ext family (like reiser4), that's why I stated in instruction to modify - instead of delete - line in rcS-late, containing mount options for reiser4. The same apply for genfstab.awk - I stated it should be only modified for ext filesystem family. So, for reiser4 and other no ext filesystems, instructions remain same as made by original author.

If someone have experience with changing filesystem other to ext4 (or any ext), and/or like to experiment with setting genfstab.awk, please update this article with Your findings.
</li>
</ol>
</li>
<li>
Reboot your phone. You're done now.
</li>
</ol>

=== Solution #2: Easier GUI solution, need another PC + linux live CD===

Coming soon - will write instructions based on use of gParted,Aptosid, or any other Linux liveCD and backupmenu (or backupmenu-multiboot). Inspired by main (GUI) solution in "repartitioning the flash" article.

== Some initial benchmarks ==
''Note from author: The benchmarks below are pretty limited, feel free to substitute them with more extended/reliable ones.''

How the benchmarks were performed: Reflashed & repartitioned phone in offline mode, SSH over usb. Used script (first round out of five dismissed in the averaged result):
<source lang="bash">
#!/bin/sh
for run in `seq 1 5`
do
sync
echo 3 > /proc/sys/vm/drop_caches
sleep 1
time sh -c "cp [FILE/DIRECTORY] /mnt && sync"
done

df | grep /mnt
</source>

The files were copied from <code>/dev/mmcblk0p1</code> (FS: reiser4, LZO compression) to <code>/dev/mmcblk0p2</code> (FS: depends on test)

Used ext3 options:
 mkfs.ext3 /dev/mmcblk0p2
 mount -t ext3 -o rw,noatime,errors=continue,commit=1,data=writeback /dev/mmcblk0p2 /mnt

Used ext4 options:
 mkfs.ext4 /dev/mmcblk0p2
 mount -t ext4 -o rw,noatime,errors=continue,commit=1,data=writeback /dev/mmcblk0p2 /mnt

Used reiser4 options:
 mkfs.reiser4 -o create=ccreg40,compress=lzo1,cluster=8K,formatting=smart /dev/mmcblk0p2
 mount -t reiser4 -o noatime /dev/mmcblk0p2 /mnt

Averaged values of the "real time" as reported by time
{| class="wikitable"
! Filesystem
! linux-2.6.28.tar.bz2 @ 50.2MiB
! 500 (mostly text) files @ 4MiB
! 83 (mostly text) files @ 14.6MiB
|-
|Ext3|| 14.3725s || 7.205s || 7.1025s
|-
|Ext4|| 9.9725s || 7.115s || 6.1625s
|-
|Reiser4|| 10.015s || 5.6625s || 5.365s
|}

Space reported by df after each benchmark (in total 747264 1K blocks available)
{| class="wikitable"
! Filesystem
! linux-2.6.28.tar.bz2 @ 50.2MiB
! 500 (mostly text) files @ 4MiB
! 83 (mostly text) files @ 14.6MiB
|-
|Ext3|| 68668 (9%) || 22748 (3%) || 32368 (4%)
|-
|Ext4|| 68592 (9%) || 22700 (3%) || 32292 (4%)
|-
|Reiser4|| 51568 (7%) || 2420 (0%) || 13500 (2%)
|}

Do note that both the stock Maemo kernel and kernel-power lack Reiser4 support; you'll have to compile a kernel with Reiser4 support yourself.

== Remarks about filesystems ==
''Please extend this text as you encounter stuff worthy to take note of.''
*Reiser4 has some problems with both cluster=8K and cluster=16K on the N900 ("<code>Wrong level found in node</code>" warnings in dmesg). The parameters cluster=32K and cluster=64K (the default value) work without error. Use these values to prevent potential data loss.

The following options have been tested by creating a tarball of /home/opt (~400MiB), extracting it once mounted, removing the original tar and then repeating for a tarball of the SDK (~500MiB). Originally cluster=8K was attempted but a reboot produced the dreaded <code>Wrong level found in node</code> error again so reverting to 32K

'''Take note of the fsck.reiser4 stage which should be executed before the first mount.''' It creates lost+found directory and inserts an entry for ".", amongst other fixes.

mkfs.reiser4 -y -o create=ccreg40,compress=lzo1,compressMode=ultim,cluster=32K,fibration=ext_3_fibre,formatting=smart /dev/mmcblkXpY
 fsck.reiser4 -y --build-fs /dev/mmcblkXpY
 mount -t reiser4 -o rw,noatime,nodiratime /dev/mmcblkXpY /path/to/mount

== Different filesystem in action ==
[[Image:screenshot_reiser4.png|Reiser4 in action]]

[[Category:N900]]
[[Category:Power users]]

Please note that all contributions to maemo.org wiki may be edited, altered, or removed by other contributors. If you do not want your writing to be edited mercilessly, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource (see maemo.org wiki:Copyrights for details). Do not submit copyrighted work without permission!

Summary:

Cancel | Editing help (opens in new window)

Retrieved from "http://wiki.maemo.org/Changing_the_eMMC_filesystem"

Personal tools

Navigation

Views

Editing Changing the eMMC filesystem

@@ Line 89: / Line 89: @@
 File <code>/usr/lib/genfstab.awk</code> also contain ext3 hardcoded in it (line 19 in vanilla Maemo, line 20 in latest CSSU-Testing). For switching to another ext filesystem (like ext4) change it to appropriate value.
-On systems with [[CSSU]], one also need to edit <code>/etc/default/mount-opts</code>, which contain mount options, including filesystem type (ext3 by default, manual modification required).
 <code>//Note for Geeks:</code>