Editing N900 Hardware USB Host
Warning: You are not logged in.
Your IP address will be recorded in this page's edit history.
The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision | Your text | ||
Line 6: | Line 6: | ||
USB Host mode has reached beta status, and is working reliably with manual speed switching. | USB Host mode has reached beta status, and is working reliably with manual speed switching. | ||
- | Proper host mode would only require the normal cable, and a commonly available adapter. ([http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=250641334947 USB A-A adaptor]) | + | Proper host mode would only require the normal cable, and a commonly available adapter. ([http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=250641334947 USB A-A adaptor]) |
A pre-alpha of hostmode was released on the 23rd of September, here: http://talk.maemo.org/showthread.php?p=824298 | A pre-alpha of hostmode was released on the 23rd of September, here: http://talk.maemo.org/showthread.php?p=824298 | ||
Line 36: | Line 36: | ||
*If the supply is a charger (D+,D- short, detected by the 1707a), fast charge. | *If the supply is a charger (D+,D- short, detected by the 1707a), fast charge. | ||
*Attempt to enumerate as a device, if this succeeds (including handling of suspended busses), then enumerate and charge as a device, respecting the enumerated current. | *Attempt to enumerate as a device, if this succeeds (including handling of suspended busses), then enumerate and charge as a device, respecting the enumerated current. | ||
- | *If | + | *If enumeration as a device, and charger detection have failed, we may be plugged into a hub or device with reverse power. Attempt to enumerate connected devices. Charge at user-defined maximum current. For example - may be a 500mA power supply also supplying the hub and a keyboard = 2 unit loads - max draw = 300mA. |
==Installation== | ==Installation== | ||
- | Install hostmode-gui from -devel, kernel | + | Install hostmode-gui from -devel, your kernel will be replaced. |
- | + | apt-get install hostmode-gui | |
- | |||
- | " | + | == Warning: == |
- | + | Uninstalling "h-e-n" might brick your device. However, it's easy to restore it to a working state by re-flashing the kernel. | |
- | + | '''Steps:''' | |
- | + | *download http://tablets-dev.nokia.com/nokia_N900.php?f=RX-51_2009SE_20.2010.36-2_PR_COMBINED_MR0_ARM.bin | |
- | + | *download flasher for your system from http://tablets-dev.nokia.com/maemo-dev-env-downloads.php and install it | |
- | + | *Turn off your device | |
- | + | *Plug-in usb cable into n900 | |
- | The | + | *open console and run flasher-3.5 -F RX-51_2009SE_20.2010.36-2_PR_COMBINED_MR0_ARM.bin --flash-only=kernel -f -R |
- | + | The .bin file has to be in the "current" directory. | |
- | + | * Initiate flashing by pressing enter | |
+ | * Turn on your device, slide-down keyboard and press "U" | ||
+ | * Wait until flashing is finished | ||
+ | * You should get a working phone with all of your programs and settings. | ||
== Devices == | == Devices == | ||
Line 65: | Line 67: | ||
== Demos == | == Demos == | ||
* http://www.youtube.com/watch?v=zDzUG-bno6Q by MohammadAG (usb CD-ROM) | * http://www.youtube.com/watch?v=zDzUG-bno6Q by MohammadAG (usb CD-ROM) | ||
- | * http://www.youtube.com/watch?v= | + | * http://www.youtube.com/watch?v=1Qfx_jaQ9jo&NR=1 by divan0 (usb HDD via usbhub) |
- | + | ||
- | + | ||
* http://www.youtube.com/watch?v=9byE_qTl15M by divan0 (usb keyboard) | * http://www.youtube.com/watch?v=9byE_qTl15M by divan0 (usb keyboard) | ||
- | |||
- | |||
- | |||
==Hostmode development team:== | ==Hostmode development team:== |
Learn more about Contributing to the wiki.