Kernel Power

Latest revision as of 01:38, 3 July 2016

The enhanced kernel "kernel-power" is compatible with PR1.2 and PR1.3, contain lots of additional features (IPv6, NAT etc) and bugfixes. The kernel can be installed via Application manager from the System section. Installation of the customization package Kernel-Power-Settings is sufficient, as it depends on the kernel page.

The custom kernel contains additional modules for IPv6, packet filtering, QoS, NAT, tunneling, kernel configuration, Wifi mesh networking, builtin ext3 for booting from other media, ext4, XFS, reiserfs, NTFS read support, ISO9660, UDF, CIFS, automounter, squashfs, unionfs, device mapper and dm-loop, cryptography, cryptoloop, EFI partitions, UTF8 codepages, mouse+joystick input, PPP, PPTP, serial support, USB hostmode (h-e-n), USB/IP and generic USB device drivers, battery info, overclocking and kexec support.

Note: This page is under construction and based on the overclocking/undervolting instructions. Hence the heavy bias to overclocking. For overclocking it includes a large set of possible frequencies (125 MHz-1.15 GHz) which you manually set and try out without flashing a new kernel. The defaults are set to the standard 250-600 MHz range. You can also fine tune the voltages for your device for power-saving. Every device is different.

talk.maemo.org: Discussion of the enhanced kernel Discussion of the enhanced kernel beginning with version 47

Changes between versions are announced on the garage page.

[edit] Installing kernel-power

Note: All commands on this page must be run as root in X Terminal (install rootsh package and enter "root")

Note: The power kernel may not be compatible with the currently-installed fcam-drivers package. Should you lose camera functionality, you can update them by running as root:

apt-get install fcam-drivers

Note: This probably won't work and you'll probably need to install fcam-drivers-1.0.7-2 from extras-devel: http://repository.maemo.org/extras-devel/pool/fremantle/free/f/fcam-drivers/fcam-drivers_1.0.7-2_armel.deb install with dpkg -i command

[edit] Installing the Stable Kernel

With this kernel you can change the frequency limits, the voltages and DSP frequencies online. It requires firmware PR1.1 or newer.

Install the package kernel-power-settings (section system in Application manager). It will automatically also install kernel-power-flasher.
Shutdown the device, and boot it up again.
The kernel is now installed.

[edit] Installing the Unstable Kernels

This kernel version contains additional experimental features and patches.

Just enable the Extras-testing or Extras-devel catalogue and install according to these instructions.

Please follow the QA checklist and vote for the package to allow promotion to Extras.

[edit] Verifying Proper Installation

First verify, that the kernel is actually running:

uname -r

should return "2.6.28.10power<version>". If it does not, you should reboot or try to install the kernel again.

[edit] Upgrade from older versions (< maemo24)

The kernel package was previously called kernel-flasher-maemo. Unfortunately, Application Manager does not support package transitions, i.e. installation of the new version leads to conflicts with kernel-maemo and kernel-modules-maemo. If you have one of the older packages installed it you need to upgrade in X Terminal.

root
apt-get install -y kernel-power-flasher
apt-get remove kernel-flasher-maemo

If the new kernel still doesn't boot up, try

apt-get install --reinstall -y kernel-power kernel-power-flasher

Also try other hints for uninstalling the old package.

Make sure you reset /etc/pmconfig to the defaults:

# Power management configuration file
enable_off_mode 1
sleep_while_idle 1
sr_vdd1_autocomp 0
sr_vdd2_autocomp 0
clocks_off_while_idle 1
voltage_off_while_idle 1
scaling_governor ondemand
scaling_max_freq 600000
scaling_min_freq 125000
sleep_ind 1

[edit] Uninstalling kernel-power

Do not try to uninstall the "kernel-power" package in Application Manager! This does not remove the kernel, as it is installed in the device's NAND.

You never want to uninstall a kernel, as your device can't work without a kernel.

[edit] Installing the Nokia Kernel with X Terminal

The standard process for replacing the kernel is as follows:

Ensure that you have a working Internet connection.
Install the package rootsh. (available in the System section of the Application Manager)
Close the Application Manager.
Gain root permissions
```
sudo gainroot
```

Reinstall the stock Nokia kernel

apt-get install --reinstall -y kernel kernel-flasher

Should it complete successfully (with "SIGTERM received" and "Image flashed successfully" messages), then you can continue with
```
apt-get remove -y kernel-power kernel-power-modules
```

After uninstallation, the command

ls -l /lib/modules/current

should show:

... /lib/modules/current -> 2.6.28-omap1

Shutdown the device (without any USB cable connected) and boot again.
The stock kernel should now be installed.

[edit] Installing the Nokia Kernel (Graphical Method)

If you have a recent kernel (>v27), there is a "Deinstall kernel" application in your menu. This application is however, still experimental (for >v27 it is more stable). Only use if have can fall back to reflashing the kernel using the flasher (see below) in case of problems. Read the instructions carefully when you start the deinstall application!

[edit] Installing the Nokia Kernel with flasher-3.5

If the device fails to boot or you have other problems, perform the uninstallation from a PC with USB cable and the flasher-3.5 utility: NOTE: This only works for kernel-power v28 and later. Versions prior to 28 interfere with system files, and may not work properly with the stock Nokia kernel.

Make sure your battery is properly charged (if it fails, charge your battery)
Execute the following on your PC (see this for more details)
```
flasher-3.5 -f --flash-only=kernel -R -F <firmware-image>
```

The firmware image file could be, for example, RX-51_2009SE_3.2010.02-8_PR_COMBINED_MR0_ARM.bin. This is only way of deinstallation with leaked release 1.2 firmware.

[edit] Upgrading to a new PR

Before upgrading, always make a backup. There are two ways of upgrading the firmware to a new Nokia public release (PR):

reflashing the complete firmware via flasher or NSU. This is safest way (especially for PR1.2). In this case you simply reinstall the kernel after the upgrade. The settings should be restored by the backup application.
Over The Air (OTA) upgrade: this upgrades only system components of your device so that you don't need to restore your settings or reinstall applications. see below

OTA upgrade: Disable extras-devel and extras-testing. DIsable autodisconnect if is installed. Perform the upgrade. If the PR does not deliver a new kernel (PR1.1.1) then you're done. If it provides a new kernel (PR1.1 and PR1.2) then you need to reinstall the enhanced kernel with the following commands:

root
apt-get install --reinstall kernel-power kernel-power-modules kernel-power-flasher

[edit] Holding a specific kernel version

If your manually installed kernel should be not upgraded to the one in extras* try this:

echo kernel-power-flasher hold | dpkg --set-selections
echo kernel-power hold | dpkg --set-selections
echo kernel-power-modules hold | dpkg --set-selections

to unlock the version:

echo kernel-power-flasher install | dpkg --set-selections
echo kernel-power install | dpkg --set-selections
echo kernel-power-modules install | dpkg --set-selections

[edit] Issues after multiboot or Nitdroid installation

Multiboot changes the boot process and might not load kernel-power properly. This is not a kernel-power problem. Please read the multiboot threads or Nitdroid forums. For versions >=v39 typically,

apt-get install kernel-power-bootimg
apt-get install --reinstall multiboot-kernel-power

adds kernel-power to your boot menu.

[edit] Features

[edit] Configuring the kernel speed/voltage settings

The instructions on the Overclocking page require the kernel-power-flasher >=v27 and kernel-power-settings >=0.8.

If you upgraded from the old stable version the old settings should still work and be loaded during boot.

NOTE: The kernel settings are not loaded after a crash. In that case the file /etc/kernel-power/.notloaded is created and a notification will be shown after booting. The settings will be loaded at the next boot again unless it crashes again.

[edit] Battery

bq27200.ko module conflicts with bme battery charging! A "fix" temporarily added to I2C driver broke system completely and thus got reverted In kernels version >=maemo20 you can read out the current battery info:

modprobe bq27x00_battery
cat /sys/class/power_supply/bq27200-0/capacity
cat /sys/class/power_supply/bq27200-0/voltage_now
cat /sys/class/power_supply/bq27200-0/current_now
cat /sys/class/power_supply/bq27200-0/temp
cat /sys/class/power_supply/bq27200-0/charge_full
cat /sys/class/power_supply/bq27200-0/charge_full_design
cat /sys/class/power_supply/bq27200-0/charge_now
cat /sys/class/power_supply/bq27200-0/time_to_empty_avg
cat /sys/class/power_supply/bq27200-0/time_to_empty_now
cat /sys/class/power_supply/bq27200-0/time_to_full_now

'capacity' value in percentage of battery level.
'voltage_now' value in mV of battery voltage level.
'current_now' value in microA of battery current consumption.
'temp' value in degrees C of battery temperature. (>= v47: in tenths of degree Celsius)

In kernel version >= v47 is additional info:

'charge_full' value in µAh - last remembered value of charge when battery became full
'charge_full_design' value in µAh - design charge value, when battery considered full
'charge_now' value in µAh - actual charge value
'time_to_empty_avg' averaged value - seconds left for battery to be considered empty (i.e. while battery powers a load)
'time_to_empty_now' seconds left for battery to be considered empty (i.e. while battery powers a load)
'time_to_full_now' seconds left for battery to be considered full (i.e. while battery is charging)

To remove this kernel module use:

rmmod bq27x00_battery

or reboot.

With kernel-power-settings >=0.6 the module can be loaded on boot. Just execute this once:

root
echo bq27x00_battery >> /etc/modules

With kernel version >= v47 the bq module is automatically loaded on boot. To disable, blacklist bq27x00_battery module:

root
echo bq27x00_battery >> /etc/modprobe.d/blacklist

[edit] Mobile Hotspot

all necessary modules are included. read this for more details.

[edit] JoikuSpot

seems to work. read this post.

Update: it doesn't work for me (recent version of Joikuspot and Maemo), ICMP and DNS resolving work OK, but TCP connections are completely freezed...If it works for you, let us know.

[edit] CIFS Support

You can now mount a network drive using Microsoft's CIFS protocol. To do so you need to do the following:

Share a folder on your Windows PC, with the latest versions of Windows you will have to create a user account with a password to share a specific folder that is not the Public Library.

Create a folder for the mount, pressumably on your /home/users/MyDocs folder, so that you could access your network drive through the file manager.

Mount the folder on your device by typing the following into xterm under root:

mount -t cifs //netbiosname/sharename /media/sharename -o user=winusername,pass=winpassword,ip=destip,direct

[edit] kexec

All necessary kexec patches are included. read [1] and this post for MeeGo support.

[edit] Boot Options

There is a separate file /etc/default/kernel-boot for extra boot options. It requires kernel-power-settings >= 0.11 and is disabled by default. These two options are experimental and may brick your device! Just install the template with the following commands and edit it (by default the options are disabled)

root
cp /usr/share/kernel-power-settings/boot /etc/default/kernel-boot

The default template looks like this

# start USB networking and sshd early during boot
EARLY_SSH=0
# fsck of /home partition before mounting?
# 1=if necessary, force=always check
FSCK_HOME=0

[edit] Filesystem Checking and Repair, and pre-mount Scripts

See above for enabling this feature. The following operations are performed before mounting /home:

If you have a script (e.g. for repartitiong) called /etc/kernel-power/pre-mount.once it will be executed once and then moved away.
if FSCK_HOME is enabled the /home partition (first ext3 on eMMC) will be fscked on boot.

Alternatively,

root
echo 1 > /etc/kernel-power/force_fsck

should check it only during next boot.

root
echo 0 > /etc/kernel-power/force_fsck

disables it only for the next boot. If you reset or reboot the device during fsck, it will not fsck (only) during the next boot. All messages are logged to /etc/kernel-power/pre-mount.log

[edit] IPv6

IPv6 support is enabled and many users are successfully using it. Note however, not all applications are IPv6 compatible.

So far, it has been successfully used with Chromium and Firefox out of the box. To run with the MicroB browser, you need to change one of the settings.

The setting is 'network.dns.disableIPv6' in about:config. When set to false, IPv6 just works when the phone has IPv6 connectivity.

IPv6 has also been used successfully with ssh and sshd.

Please share additional experiences here.

[edit] PPTP

tutorial

[edit] Kismet

tutorial and TMO thread

[edit] Other Filesystems

The kernel includes support for many alternative filesystems, including ext4 bugfixes and large file support. You might want to repartition your eMMC or SD card with Repartitioning_the_flash.

[edit] Notes

even if 125 Mhz is disabled, the telephone app will always try to set the minimum freq. to 125 Mhz after a phone call, but it is ignored unless you enable 125 Mhz.
if you enable 125 MHz also set "echo 1 > /sys/devices/system/cpu/cpu0/cpufreq/ondemand/ignore_nice_load" hint
the 125 MHz issue
Installing another version of the enhanced kernel will just overwrite the older version. The stock kernel modules are preserved so that you can simply reflash the stock kernel via USB.
The kernel supports 125 MHz but this frequency is disabled by default in avoid_frequencies. In version <25, it is enabled by specifying "124999", in later versions it is disabled in /sys/devices/system/cpu/cpu0/cpufreq/ondemand/avoid_frequencies and can be enabled with:
```
echo > /sys/devices/system/cpu/cpu0/cpufreq/ondemand/avoid_frequencies
```
similarily, individual frequencies can be disabled in >=v25:
```
echo 125000 250000 750000 > /sys/devices/system/cpu/cpu0/cpufreq/ondemand/avoid_frequencies
```

Retrieved from "http://wiki.maemo.org/Kernel_Power"

Categories: Power users | N900

This page was last modified on 3 July 2016, at 01:38.
This page has been accessed 355,181 times.

@@ Line 17: / Line 17: @@
 '''Note: The power kernel may not be compatible with the currently-installed fcam-drivers package.''' Should you lose camera functionality, you can update them by running as root:<pre>apt-get install fcam-drivers</pre>
+'''Note:''' This probably won't work and you'll probably need to install fcam-drivers-1.0.7-2 from extras-devel:
+http://repository.maemo.org/extras-devel/pool/fremantle/free/f/fcam-drivers/fcam-drivers_1.0.7-2_armel.deb
+install with ''dpkg -i'' command
 ===Installing the [http://maemo.org/downloads/product/Maemo5/kernel-power-flasher/ Stable Kernel]===

Personal tools

Navigation

Views